• Nov 18, 2026
  • 0 comments

CADlink Digital Factory V12 for Audley DTF Printers: Which Edition You Need + Setup Guide

Short answer: Yes, CADlink Digital Factory V12 runs Audley DTF printers. For Audley's 13-inch / A3 models, the Desktop Edition ($379.99) is the right license. For every Audley 24-inch printer (2-head, 4-head or 6-head), you need the Large Format / Production Edition ($799.99). Below you'll find a model-by-model breakdown, the setup steps, and how to test your exact Audley before you pay anything.

DTF Gears is the only US dropship seller for Audley and an Official Fiery (CADlink) Premier Partner, so this guide covers both sides of the setup: the printer and the RIP that drives it.

Does CADlink Digital Factory support Audley printers?

Yes. CADlink's DTF printer driver list includes these Audley drivers:

  • Audley 24 (2 Heads)
  • Audley 24 (4 Heads)
  • Audley 24 XP (2 Heads)
  • Audley Mini 13
  • Audley TF300 (Sunyung board)

One detail most buyers miss: CADlink matches drivers by printer model and controller board, not just print width. Audley builds use different boards (for example Sunyung on smaller models, Hoson on some 24-inch models). Before you buy a license, confirm that your exact model and board show up in the printer list during setup. The free trial (covered below) is the easiest way to check.

For the full list of non-Audley printers, see our CADlink V12 supported printers guide.

Which CADlink V12 edition does your Audley need?

Fiery splits Digital Factory V12 DTF into two editions by printer size:

  • Desktop Edition: printers up to A2 sheet size or roughly 17–18-inch roll width.
  • Production (Large Format) Edition: large-format and production-class DTF printers, including 24-inch roll printers. It also adds multi-printer support and advanced queue management.

Here's how that maps to the Audley lineup:

Audley printer Print width CADlink driver to look for Edition you need
Audley A3 / 13" models (e.g. Audley Mini 13) Up to 13" Audley Mini 13 / Audley TF300 Desktop – $379.99
Audley 24" 2-head (e.g. 8072-3 Wi-Fi, S7070-3) 24" Audley 24 (2 Heads) / Audley 24 XP (2 Heads) Large Format – $799.99
Audley 24" 4-head (e.g. S8074-3) 24" Audley 24 (4 Heads) Large Format – $799.99
Audley 24" 6-head (e.g. 8076-3) 24" Confirm in trial before buying Large Format – $799.99

Rule of thumb: If your Audley prints on 24-inch film, buy the Large Format Edition. The Desktop license won't drive a 24-inch printer, and buying the wrong edition is the most common (and most avoidable) RIP mistake we see.

Already know your model? Get the right CADlink V12 license with instant activation (no dongle).

Shop CADlink V12 Editions →

Why run CADlink on an Audley instead of the bundled RIP?

Many Audley packages ship with a basic RIP that prints fine. Shops switch to CADlink when they want production control over their 24-inch output:

  • White ink automation: automatic white underbase and highlight white, so you aren't hand-building white layers for every design. On a 24-inch printer running all day, that saves real ink.
  • Fiery color engine and ICC profiles: consistent, accurate color across reorders. That matters when a client compares this month's shirts to last month's.
  • Gang Sheet Builder (new in V12): import multiple designs and lay out full 24-inch gang sheets inside Digital Factory, with no separate layout app.
  • Multi-lane roll printing (V12.1): the June 2026 update added multi-lane support for roll printing, which suits high-volume Audley roll-to-roll work.
  • Queue control, hot folders and barcodes: drop files into a hot folder and they print in order. Barcodes and print labels keep jobs organized when you're shipping transfers.
  • Multi-printer support (Production Edition): run your Audley alongside a second DTF printer from one workstation as your shop grows.

How to set up CADlink Digital Factory V12 with your Audley

  1. Check your PC. Digital Factory V12 runs on Windows 10 or 11. Use a dedicated production PC with an SSD and 16 GB RAM if you can, because 24-inch gang sheets are large files. On a Mac? Read can you run CADlink on a Mac first.
  2. Install and activate. Download Digital Factory V12 and enter your activation code. DTF Gears licenses are digital, with instant activation and no dongle. Step-by-step screenshots are in our CADlink V12 Windows install guide.
  3. Add your Audley as a printer. In the printer setup, choose Audley as the manufacturer, then the driver that matches your model and head count (see the table above). This is where you confirm your board is supported.
  4. Connect the port. Select the connection your Audley uses (network/TCP-IP or USB). Then send a nozzle check from the printer itself first, so you know the heads are clean before you blame the RIP.
  5. Load the right print mode and color profile. Pick the print mode and ICC profile for your ink and film combination. Matching the profile to your actual consumables is what gets you accurate color on the first run.
  6. Set your white ink. Choose your white underbase settings (density and choke) and decide when to use highlight white. Start with the defaults, print a test, then fine-tune.
  7. Turn on roll mode and nesting. On a 24-inch Audley, set roll mode and auto-nesting so CADlink packs designs edge-to-edge and wastes less film.
  8. Run a test gang sheet. Print a sheet with a skin-tone photo, a solid black, a gradient and fine text. If all four look right after powder and cure, you're production-ready.

Test your Audley with CADlink before you buy

You don't have to guess. DTF Gears offers a free 15-day CADlink trial. Install it, add your Audley, and confirm your driver and board appear before you spend anything. Get the CADlink free trial here.

If you start on Desktop with a 13-inch Audley and later move up to a 24-inch model, Fiery offers a Desktop-to-Production upgrade path, so you aren't locked in.

Still choosing your Audley?

If you're pairing the RIP with a new printer, compare the full lineup on our Audley DTF printers page. Every Audley printer is sold as a printer + powder shaker set with free US shipping. For shops moving past desktop machines, the commercial DTF printers guide explains when a 24-inch, 4-head or 6-head setup pays off.

Starting smaller? The Audley A3 DTF printer + powder shaker bundle runs on the CADlink Desktop Edition.

Need to spread the cost? Audley printers qualify for DTF printer financing through our lending partners.

Audley + CADlink, from one US partner

Printer, shaker and RIP license, with setup help from our DTF team.

Shop Audley Printers Shop CADlink V12

FAQ: CADlink and Audley DTF printers

Does CADlink Digital Factory V12 work with Audley DTF printers?

Yes. CADlink includes Audley drivers such as Audley 24 (2 Heads), Audley 24 (4 Heads), Audley 24 XP (2 Heads), Audley Mini 13 and Audley TF300. Confirm your exact model and controller board in the free trial before buying.

Which CADlink edition do I need for an Audley 24-inch printer?

The Large Format / Production Edition ($799.99). The Desktop Edition covers printers up to about 17–18 inches wide, so it won't run a 24-inch Audley.

Which CADlink edition do I need for an Audley A3 or 13-inch printer?

The Desktop Edition ($379.99) covers Audley's 13-inch / A3 class printers.

Can I run an Audley and another DTF printer on one CADlink license?

The Production Edition is built for multi-printer environments. The Desktop Edition supports one printer, and you can add another with a Desktop add-on printer port.

Can I upgrade from Desktop to Large Format later?

Yes. Fiery offers a Desktop-to-Production upgrade, so you can start with a 13-inch Audley and move to a 24-inch model without buying a brand-new license from scratch.

Does CADlink run on a Mac?

Digital Factory V12 officially runs on Windows 10 and 11. See our Mac guide for workarounds.